hi list, i am new here and just trying to use batman rev350 compiled on 2.6.21.1-rt3 kernel on ibm-thinkpad-R50e. the rt-patch (for low-latency audio work) comes from:
http://people.redhat.com/mingo/realtime-preempt/
i am using a atmel-wlan adapter and the atmel driver from:
git-clone http://honk.sigxcpu.org/git/at76c503a.git/
the driver runs pretty stable, if i use olsrd to join the network here, i use following script to start the protocol:
#!/bin/sh iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ap 02:CA:FF:EE ifconfig eth2 104.130.30.9 ifconfig eth2 up olsrd
.........
except of some timeouts, which are pretty rarely, that runs good.
i am starting batman with:
#!/bin/bash iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ifconfig eth2 105.130.30.9 ifconfig eth2 up sleep 1 batmand -d 1 -p 105.131.41.5 -r 1 eth2
and
#!/bin/bash batmand -c -d 2
in another terminal.
when batman starts, the 'batmand -c' script shows, that i am connected to another gateway, but not to preferred one:
Gateway Router (#/128) => 105.192.99.62 105.130.30.1 ( 3), gw_class 10 - 6 MBit, reliability: 0 105.192.99.61 105.130.30.1 ( 1), gw_class 7 - 2 MBit, reliability: 0 105.131.83.5 105.130.30.1 ( 1), gw_class 11 - >6 MBit, reliability: 0 105.131.41.5 105.130.30.1 ( 2), gw_class 11 - >6 MBit, reliability: 0 105.192.99.103 105.130.30.1 ( 3), gw_class 7 - 2 MBit, reliability: 0 105.192.99.192 105.130.30.1 ( 2), gw_class 10 - 6 MBit, reliability: 0
...........
this always is a number 105.192.99.....(.62, .103, .192). this condition than stays for 2 or 3 up to 10 minutes, and in that time i cannot even ping the 105.130.30.1 which is the next point here.
after some minutes, the connection changes, so that 'batmand -c' shows that i am connected to 105.131.41.5 and i am able to ping 141.1.1.1. unfortunately, after some minutes (or even shorter), the batman script stops and the terminal is at the prompt again. there is no segfault, using 'ulimit -c unlimited' will not produce a core-dump. i suppose that this is not a driver bug, cause looking at this moment at 'dmesg', i can see that the driver is loaded using the 02:ca:ff:ee:ba:by - if i stop batmand and start olsrd, i will be connected to the internet as expected.
i am really not aware of what else information i could provide to you, in order to make batmand running stable here, but if you have any idea, please let me know!
cheers, doc
Hey Dragan,
#!/bin/sh iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ap 02:CA:FF:EE ifconfig eth2 104.130.30.9
(just to be shure) this should be 02:CA:FF:EE:BA:BE
..
i am starting batman with:
#!/bin/bash iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ifconfig eth2 105.130.30.9 ifconfig eth2 up sleep 1 batmand -d 1 -p 105.131.41.5 -r 1 eth2
can you start batmand in background with: batmand -r 1 -p 105.131.41.5 eth2 instead and tell if the problem continues. This command instantly returns your prompt but a: ps -aux | grep batmand should show the running main-daemon in the background. Also please check that there are no predefined host routes for the 105.0.0.0/8 network before you start batmand and after it stopped. Meaning a: route -n | grep ^105 berfore and after the daemon is running should only show: 105.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth2 While batmand is running it should of course show routing entries for all other known batman nodes but if such host routes are still there after the daemon stopped it is a definitive sign for an uncorect termination of teh daemon.
#!/bin/bash batmand -c -d 2
in another terminal.
It should of course always be possible to access the debug output from the running batmand main-daemon by launching a batmand-client with batmand -c -d <1-4> or in batch mode (providing just a single outputpage and returns to the prompt) with: batmand -c -d <1-4> -b However, it would be interesting to know if the crash is related to existence of a batmand-client connecting to the main daemon. For example for batmand-0.2.0-rc2-rv350 (and before) debug level 4: batmand -c -d 4 is known to cause the batmand to crash after a short time and it might be possible that this problems also occur with other debug-levels. Try batmand -c -d 1 and batmand -c -d 2 instead.
ciao, axel
when batman starts, the 'batmand -c' script shows, that i am connected to another gateway, but not to preferred one:
Gateway Router (#/128)=> 105.192.99.62 105.130.30.1 ( 3), gw_class 10 - 6 MBit, reliability: 0 105.192.99.61 105.130.30.1 ( 1), gw_class 7 - 2 MBit, reliability: 0 105.131.83.5 105.130.30.1 ( 1), gw_class 11 - >6 MBit, reliability: 0 105.131.41.5 105.130.30.1 ( 2), gw_class 11 - >6 MBit, reliability: 0 105.192.99.103 105.130.30.1 ( 3), gw_class 7 - 2 MBit, reliability: 0 105.192.99.192 105.130.30.1 ( 2), gw_class 10 - 6 MBit, reliability: 0
...........
this always is a number 105.192.99.....(.62, .103, .192). this condition than stays for 2 or 3 up to 10 minutes, and in that time i cannot even ping the 105.130.30.1 which is the next point here.
after some minutes, the connection changes, so that 'batmand -c' shows that i am connected to 105.131.41.5 and i am able to ping 141.1.1.1. unfortunately, after some minutes (or even shorter), the batman script stops and the terminal is at the prompt again. there is no segfault, using 'ulimit -c unlimited' will not produce a core-dump. i suppose that this is not a driver bug, cause looking at this moment at 'dmesg', i can see that the driver is loaded using the 02:ca:ff:ee:ba:by - if i stop batmand and start olsrd, i will be connected to the internet as expected.
i am really not aware of what else information i could provide to you, in order to make batmand running stable here, but if you have any idea, please let me know!
cheers, doc _______________________________________________ B.A.T.M.A.N mailing list B.A.T.M.A.N@open-mesh.net https://list.open-mesh.net/mm/listinfo/b.a.t.m.a.n
Axel Neumann wrote:
Hey Dragan,
#!/bin/sh iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ap 02:CA:FF:EE ifconfig eth2 104.130.30.9
(just to be shure) this should be 02:CA:FF:EE:BA:BE
of course, it was a copy+paste issue...
..
i am starting batman with:
#!/bin/bash iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ifconfig eth2 105.130.30.9 ifconfig eth2 up sleep 1 batmand -d 1 -p 105.131.41.5 -r 1 eth2
can you start batmand in background with: batmand -r 1 -p 105.131.41.5 eth2 instead and tell if the problem continues. This command instantly returns your prompt but a: ps -aux | grep batmand should show the running main-daemon in the background.
that looks good in the moment here! it is connecting to the preferred gateway very fast, but again it stops after some minutes (running 'batmand -c -d 2' in another terminal).
Also please check that there are no predefined host routes for the 105.0.0.0/8 network before you start batmand and after it stopped. Meaning a: route -n | grep ^105 berfore and after the daemon is running should only show: 105.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth2 While batmand is running it should of course show routing entries for all other known batman nodes but if such host routes are still there after the daemon stopped it is a definitive sign for an uncorect termination of teh daemon.
this is strange, after killing batmand, sometimes this command will give out a long list of nodes, and sometimes it is behaving as you are expecting it.
#!/bin/bash batmand -c -d 2
in another terminal.
It should of course always be possible to access the debug output from the running batmand main-daemon by launching a batmand-client with batmand -c -d <1-4> or in batch mode (providing just a single outputpage and returns to the prompt) with: batmand -c -d <1-4> -b However, it would be interesting to know if the crash is related to existence of a batmand-client connecting to the main daemon. For example for batmand-0.2.0-rc2-rv350 (and before) debug level 4: batmand -c -d 4 is known to cause the batmand to crash after a short time and it might be possible that this problems also occur with other debug-levels. Try batmand -c -d 1 and batmand -c -d 2 instead.
when i am running batmand without debug and :
'batmand -c -d 2', batmand is stopping after couple of minutes.
trying now to run only batmand without -d option and no client, lets see for how long it will be running?!
cheers, doc
p.s. example, batmand was stopping now again and several minutes after it is stopped:
murija2:/home/nowhiskey# route -n | grep ^105 105.192.99.3 105.130.1.67 255.255.255.255 UGH 0 0 0 eth2 105.131.10.1 105.130.30.1 255.255.255.255 UGH 0 0 0 eth2 105.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth2 murija2:/home/nowhiskey# ...........
'ps ax' does not shows any batman process running.
but my feeling is, that when i do not start 'batmand -c' i will be connected much more faster. but this statement unfortunately is not very informative.
ciao, axel
Dragan Noveski wrote:
Axel Neumann wrote:
Hey Dragan,
#!/bin/sh iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ap 02:CA:FF:EE ifconfig eth2 104.130.30.9
(just to be shure) this should be 02:CA:FF:EE:BA:BE
of course, it was a copy+paste issue...
..
i am starting batman with:
#!/bin/bash iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ifconfig eth2 105.130.30.9 ifconfig eth2 up sleep 1 batmand -d 1 -p 105.131.41.5 -r 1 eth2
can you start batmand in background with: batmand -r 1 -p 105.131.41.5 eth2 instead and tell if the problem continues. This command instantly returns your prompt but a: ps -aux | grep batmand should show the running main-daemon in the background.
that looks good in the moment here! it is connecting to the preferred gateway very fast, but again it stops after some minutes (running 'batmand -c -d 2' in another terminal).
Also please check that there are no predefined host routes for the 105.0.0.0/8 network before you start batmand and after it stopped. Meaning a: route -n | grep ^105 berfore and after the daemon is running should only show: 105.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth2 While batmand is running it should of course show routing entries for all other known batman nodes but if such host routes are still there after the daemon stopped it is a definitive sign for an uncorect termination of teh daemon.
this is strange, after killing batmand, sometimes this command will give out a long list of nodes, and sometimes it is behaving as you are expecting it.
#!/bin/bash batmand -c -d 2
in another terminal.
It should of course always be possible to access the debug output from the running batmand main-daemon by launching a batmand-client with batmand -c -d <1-4> or in batch mode (providing just a single outputpage and returns to the prompt) with: batmand -c -d <1-4> -b However, it would be interesting to know if the crash is related to existence of a batmand-client connecting to the main daemon. For example for batmand-0.2.0-rc2-rv350 (and before) debug level 4: batmand -c -d 4 is known to cause the batmand to crash after a short time and it might be possible that this problems also occur with other debug-levels. Try batmand -c -d 1 and batmand -c -d 2 instead.
when i am running batmand without debug and :
'batmand -c -d 2', batmand is stopping after couple of minutes.
trying now to run only batmand without -d option and no client, lets see for how long it will be running?!
cheers, doc
p.s. example, batmand was stopping now again and several minutes after it is stopped:
murija2:/home/nowhiskey# route -n | grep ^105 105.192.99.3 105.130.1.67 255.255.255.255 UGH 0 0 0 eth2 105.131.10.1 105.130.30.1 255.255.255.255 UGH 0 0 0 eth2 105.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth2 murija2:/home/nowhiskey# ...........
'ps ax' does not shows any batman process running.
but my feeling is, that when i do not start 'batmand -c' i will be connected much more faster. but this statement unfortunately is not very informative.
ciao, axel
look, i am running batman now for longer than a half hour and it did not stopped. it is running with:
#!/bin/bash iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ifconfig eth2 105.130.30.9 ifconfig eth2 up sleep 1 batmand -p 105.131.41.5 -r 1 eth2
no batman-client is running, so perhaps really this is the originally problem?!
cheers, doc
Dragan Noveski wrote:
Dragan Noveski wrote:
Axel Neumann wrote:
Hey Dragan,
#!/bin/sh iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ap 02:CA:FF:EE ifconfig eth2 104.130.30.9
(just to be shure) this should be 02:CA:FF:EE:BA:BE
of course, it was a copy+paste issue...
..
i am starting batman with:
#!/bin/bash iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ifconfig eth2 105.130.30.9 ifconfig eth2 up sleep 1 batmand -d 1 -p 105.131.41.5 -r 1 eth2
can you start batmand in background with: batmand -r 1 -p 105.131.41.5 eth2 instead and tell if the problem continues. This command instantly returns your prompt but a: ps -aux | grep batmand should show the running main-daemon in the background.
that looks good in the moment here! it is connecting to the preferred gateway very fast, but again it stops after some minutes (running 'batmand -c -d 2' in another terminal).
Also please check that there are no predefined host routes for the 105.0.0.0/8 network before you start batmand and after it stopped. Meaning a: route -n | grep ^105 berfore and after the daemon is running should only show: 105.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth2 While batmand is running it should of course show routing entries for all other known batman nodes but if such host routes are still there after the daemon stopped it is a definitive sign for an uncorect termination of teh daemon.
this is strange, after killing batmand, sometimes this command will give out a long list of nodes, and sometimes it is behaving as you are expecting it.
#!/bin/bash batmand -c -d 2
in another terminal.
It should of course always be possible to access the debug output from the running batmand main-daemon by launching a batmand-client with batmand -c -d <1-4> or in batch mode (providing just a single outputpage and returns to the prompt) with: batmand -c -d <1-4> -b However, it would be interesting to know if the crash is related to existence of a batmand-client connecting to the main daemon. For example for batmand-0.2.0-rc2-rv350 (and before) debug level 4: batmand -c -d 4 is known to cause the batmand to crash after a short time and it might be possible that this problems also occur with other debug-levels. Try batmand -c -d 1 and batmand -c -d 2 instead.
when i am running batmand without debug and :
'batmand -c -d 2', batmand is stopping after couple of minutes.
trying now to run only batmand without -d option and no client, lets see for how long it will be running?!
cheers, doc
p.s. example, batmand was stopping now again and several minutes after it is stopped:
murija2:/home/nowhiskey# route -n | grep ^105 105.192.99.3 105.130.1.67 255.255.255.255 UGH 0 0 0 eth2 105.131.10.1 105.130.30.1 255.255.255.255 UGH 0 0 0 eth2 105.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth2 murija2:/home/nowhiskey# ...........
'ps ax' does not shows any batman process running.
but my feeling is, that when i do not start 'batmand -c' i will be connected much more faster. but this statement unfortunately is not very informative.
ciao, axel
look, i am running batman now for longer than a half hour and it did not stopped. it is running with:
#!/bin/bash iwconfig eth2 mode ad-hoc essid olsr.freifunk.net channel 10 ifconfig eth2 105.130.30.9 ifconfig eth2 up sleep 1 batmand -p 105.131.41.5 -r 1 eth2
no batman-client is running, so perhaps really this is the originally problem?!
cheers, doc
ok, it is obviously now: if i start batmand without the -d option and if i do not start 'batmand -c' everything runs just smoothly!
i will be experimenting with this in the next days (probably monday) and will report my experience.
cheers, doc
Hi,
ok, it is obviously now: if i start batmand without the -d option and if i do not start 'batmand -c' everything runs just smoothly!
i will be experimenting with this in the next days (probably monday) and will report my experience.
thanks for your bug report. I just issued 2 patches. Number one reenables core dumps on segmentation fault. Batman listens for that signal and tries to clean up the routing table, interfaces, etc. Therefore batman exited gracefully and the core dump was not created.
But if batman had received SIGSEGV it would print the message "Error - SIGSEGV received !". It seems that did not happen ?! I got the idea that you may be disconnect with your client in the very moment when batman tries to write a message into the connection. The kernel would recognize the disconnect and sends SIGPIPE to batman which exits as this is the default behaviour. The second patch changes that. It is a wild guess ... :-)
Please, try it out.
Regards, Marek
Marek Lindner wrote:
Hi,
ok, it is obviously now: if i start batmand without the -d option and if i do not start 'batmand -c' everything runs just smoothly!
i will be experimenting with this in the next days (probably monday) and will report my experience.
thanks for your bug report. I just issued 2 patches. Number one reenables core dumps on segmentation fault. Batman listens for that signal and tries to clean up the routing table, interfaces, etc. Therefore batman exited gracefully and the core dump was not created.
But if batman had received SIGSEGV it would print the message "Error - SIGSEGV received !". It seems that did not happen ?! I got the idea that you may be disconnect with your client in the very moment when batman tries to write a message into the connection. The kernel would recognize the disconnect and sends SIGPIPE to batman which exits as this is the default behaviour. The second patch changes that. It is a wild guess ... :-)
Please, try it out.
Regards, Marek _______________________________________________ B.A.T.M.A.N mailing list B.A.T.M.A.N@open-mesh.net https://list.open-mesh.net/mm/listinfo/b.a.t.m.a.n
hi and thanks for the response!
since i got the core dump created now, i suppose that the patches are in rev352?
pleas tell me what to do with the core file, but for now i will attach it.
cheers, doc
b.a.t.m.a.n@lists.open-mesh.org
-
Axel Neumann -
Dragan Noveski -
Marek Lindner