OpenWrt version: Attitude Adjustment (r37747)
Recently there was someone (Lucaspost) on #batman with a problem caused by mixing the latest AA and Batman-adv 2013.3.0 and while i can't be sure the problem is exactly this one; here goes my testing with a D-link 615C1
I can only access the router using a serial connection and here is the log. attached goes the kernel configuration that i used while compiling the image.
Since i am not sure which side is causing the this problem (batman-adv or openwrt) i am emailing both lists.
[ 26.790000] Kernel panic - not syncing: Fatal exception in interrupt [ 26.800000] Rebooting in 3 seconds..
U-Boot 1.1.4 (Sep 5 2008 - 17:05:35)
AP81 (ar7100) U-boot DRAM: AP81 initdram
sri:ddr_init 32 MB Top of RAM usable for U-Boot at: 82000000 Reserving 177k for U-Boot at: 81fd0000 Reserving 192k for malloc() at: 81fa0000 Reserving 44 Bytes for Board Info at: 81f9ffd4 Reserving 36 Bytes for Global Data at: 81f9ffb0 Reserving 128k for boot params() at: 81f7ffb0 Stack Pointer at: 81f7ff98 Now running in RAM - U-Boot at: 81fd0000 ar7100 flash_init id read 0x10000107 flash size 400000, sector count = 64 Flash: 4 MB Using default environment
In: serial Out: serial Err: serial Net: eth_initialize CONFIG_NET_MULTI ag7100_enet_initialize eth0: 00:22:b0:d2:61:0b ethernet found. eth0 ## Booting image at bf030000 ... checksum:8ba30c3a Image Name: MIPS OpenWrt Linux-3.3.8 Created: 2013-08-12 3:37:29 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 924127 Bytes = 902.5 kB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum ... OK LZMA Umcompressing Kernel Image ... Image loaded from 80060000-8030ae40 OK Boot image os 5=IH_OS_LINUX ## do_bootm_linux start.... No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 33554432
##Starting kernel ...
[ 0.000000] Linux version 3.3.8 (cmsv@nixbits) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Aug 11 23:35:48 EDT 2013 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9130 rev 1 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:100.000MHz, Ref:5.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=DIR-615-C1 console=ttyS0,115200 mtdparts=spi0.0:128k(u-boot)ro,64k(config)ro,960k(kernel),2880k(rootfs),64k(art)ro,3840k@0x30000(firmware) rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 29116k/32768k available (2115k kernel code, 3652k reserved, 406k data, 208k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79 [ 0.100000] MIPS: machine is D-Link DIR-615 rev. C1 [ 0.580000] bio: create slab <bio-0> at 0 [ 0.590000] Switching to clocksource MIPS [ 0.600000] NET: Registered protocol family 2 [ 0.600000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.600000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.610000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.610000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.620000] TCP reno registered [ 0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.630000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.630000] NET: Registered protocol family 1 [ 0.660000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.660000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.670000] msgmni has been set to 56 [ 0.680000] io scheduler noop registered [ 0.680000] io scheduler deadline registered (default) [ 0.690000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.710000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.720000] console [ttyS0] enabled, bootconsole disabled [ 0.720000] console [ttyS0] enabled, bootconsole disabled [ 0.740000] m25p80 spi0.0: found s25sl032a, expected m25p80 [ 0.740000] m25p80 spi0.0: s25sl032a (4096 Kbytes) [ 0.750000] 6 cmdlinepart partitions found on MTD device spi0.0 [ 0.750000] Creating 6 MTD partitions on "spi0.0": [ 0.760000] 0x000000000000-0x000000020000 : "u-boot" [ 0.760000] 0x000000020000-0x000000030000 : "config" [ 0.770000] 0x000000030000-0x000000120000 : "kernel" [ 0.780000] 0x000000120000-0x0000003f0000 : "rootfs" [ 0.780000] mtd: partition "rootfs" set to be root filesystem [ 0.790000] mtd: partition "rootfs_data" created automatically, ofs=380000, len=70000 [ 0.800000] 0x000000380000-0x0000003f0000 : "rootfs_data" [ 0.800000] 0x0000003f0000-0x000000400000 : "art" [ 0.810000] 0x000000030000-0x0000003f0000 : "firmware" [ 0.870000] ag71xx_mdio: probed [ 0.870000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.200000] eth0: Atheros AR8216 switch driver attached. [ 1.300000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd042, driver=Atheros AR8216/AR8236/AR8316] [ 1.310000] eth1: Atheros AG71xx at 0xba000000, irq 5 [ 1.640000] ag71xx ag71xx.1: eth1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd042, driver=Atheros AR8216/AR8236/AR8316] [ 1.650000] TCP cubic registered [ 1.660000] NET: Registered protocol family 17 [ 1.660000] 8021q: 802.1Q VLAN Support v1.8 [ 1.670000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 1.680000] Freeing unused kernel memory: 208k freed - preinit - Press the [f] key and hit [enter] to enter failsafe mode [ 5.310000] eth0: link up (100Mbps/Full duplex) - regular preinit - jffs2 not ready yet; using ramdisk - init - [ 7.400000] eth0: link down [ 8.000000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5 [ 8.000000] Backport generated by backports.git backports-20130617-4-ge3220f5 [ 8.040000] cfg80211: Calling CRDA to update world regulatory domain [ 8.040000] cfg80211: World regulatory domain updated: [ 8.050000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 8.050000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.060000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 8.070000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 8.080000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.090000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.370000] usbcore: registered new interface driver usbfs [ 8.380000] usbcore: registered new interface driver hub [ 8.380000] usbcore: registered new device driver usb [ 9.070000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a1 mem=0xb80c0000, irq=2 [ 9.080000] cfg80211: Calling CRDA for country: US [ 9.080000] cfg80211: Regulatory domain changed to country: US [ 9.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 9.100000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 9.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 9.110000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.120000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.130000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.140000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 9.190000] PPP generic driver version 2.4.2 [ 9.420000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.640000] NET: Registered protocol family 24 [ 9.660000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.680000] nf_conntrack version 0.5.0 (458 buckets, 1832 max) [ 9.970000] batman_adv: B.A.T.M.A.N. advanced 2013.3.0 (compatibility version 14) loaded [ 10.030000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Please press Enter to activate this console. [ 15.580000] device eth0 entered promiscuous mode [ 17.530000] eth0: link up (100Mbps/Full duplex) [ 17.540000] br-lan: port 1(eth0) entered forwarding state [ 17.540000] br-lan: port 1(eth0) entered forwarding state [ 19.540000] br-lan: port 1(eth0) entered forwarding state [ 19.570000] cfg80211: Calling CRDA for country: PT [ 19.580000] cfg80211: Regulatory domain changed to country: PT [ 19.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 19.590000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 19.600000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 19.610000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 19.610000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm) [ 21.980000] device wlan0 entered promiscuous mode [ 22.000000] br-lan: port 2(wlan0) entered forwarding state [ 22.010000] br-lan: port 2(wlan0) entered forwarding state [ 24.010000] br-lan: port 2(wlan0) entered forwarding state [ 25.780000] br-lan: port 2(wlan0) entered disabled state [ 26.590000] CPU 0 Unable to handle kernel paging request at virtual address 00000108, epc == 801e0a88, ra == 801e0a88 [ 26.600000] Oops[#1]: [ 26.600000] Cpu 0 [ 26.600000] $ 0 : 00000000 00000000 80eefa80 80f2c030 [ 26.600000] $ 4 : 80f2c764 00000000 00000000 000001e8 [ 26.600000] $ 8 : 00000024 80165c2c 00000003 ee940fc2 [ 26.600000] $12 : 802d6204 b479fa57 25acb3af e000044c [ 26.600000] $16 : 00000000 80f2cb80 80f2cb80 81b05000 [ 26.600000] $20 : 80e97f10 80340000 80db2300 80ef6c98 [ 26.600000] $24 : 00000003 00000000 [ 26.600000] $28 : 80e96000 80e97d60 00000000 801e0a88 [ 26.600000] Hi : 000001dd [ 26.600000] Lo : 003fcd9e [ 26.600000] epc : 801e0a88 0x801e0a88 [ 26.600000] Tainted: G O [ 26.600000] ra : 801e0a88 0x801e0a88 [ 26.600000] Status: 1000f403 KERNEL EXL IE [ 26.600000] Cause : 00800008 [ 26.600000] BadVA : 00000108 [ 26.600000] PrId : 00019374 (MIPS 24Kc) [ 26.600000] Modules linked in: ath79_wdt ohci_hcd ledtrig_usbdev ledtrig_netdev batman_adv(O) nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp ipt_MASQUERADE iptable_nat nf_nat pppoe xt_conntrack xt_CT xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack ehci_hcd pppox ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc ath9k(O) ath9k_common(O) ath9k_hw(O) ath(O) mac80211(O) usbcore usb_common nls_base libcrc32c crc16 crc_ccitt cfg80211(O) compat(O) arc4 aes_generic crc32c crypto_hash crypto_algapi ledtrig_timer ledtrig_default_on leds_gpio gpio_button_hotplug(O) [ 26.600000] Process batadv.sh (pid: 1050, threadinfo=80e96000, task=80f44850, tls=77a5e440) [ 26.600000] Stack : 80279120 00000000 00000010 80f2cb80 80f48800 80ed7318 00000001 80f2c800 [ 26.600000] 80f2cb80 81b05000 00000001 80f2c800 80f2cb80 81b05000 80e97f10 80ec8808 [ 26.600000] 80ed9968 81b05000 80e97f10 00000000 00000000 80f2c800 80f2cb80 80ecf8ac [ 26.600000] 00000000 80ecf97c 00000000 00000000 80f2c800 00000000 00000000 801edc74 [ 26.600000] 80f2c800 801e8e80 80e97f00 80dad000 00000000 80f2c800 81b05000 00000000 [ 26.600000] ... [ 26.600000] Call Trace:[<80ed7318>] 0x80ed7318 [ 26.600000] [<80ec8808>] 0x80ec8808 [ 26.600000] [<80ecf8ac>] 0x80ecf8ac [ 26.600000] [<80ecf97c>] 0x80ecf97c [ 26.600000] [<801edc74>] 0x801edc74 [ 26.600000] [<801e8e80>] 0x801e8e80 [ 26.600000] [<80ed01a8>] 0x80ed01a8 [ 26.600000] [<801e8bcc>] 0x801e8bcc [ 26.600000] [<80ec7084>] 0x80ec7084 [ 26.600000] [<80ed0af8>] 0x80ed0af8 [ 26.600000] [<800b19f0>] 0x800b19f0 [ 26.600000] [<80122acc>] 0x80122acc [ 26.600000] [<800d9104>] 0x800d9104 [ 26.600000] [<800757dc>] 0x800757dc [ 26.600000] [<800d93dc>] 0x800d93dc [ 26.600000] [<8006a284>] 0x8006a284 [ 26.600000] [<8007580c>] 0x8007580c [ 26.600000] [ 26.600000] [ 26.600000] Code: afbf0014 0c078286 00808021 <8e030108> 7c6304c0 1460000a 8fbf0014 10400009 8fb00010 [ 26.870000] ---[ end trace d26ab0e286851b8a ]--- [ 26.870000] Kernel panic - not syncing: Fatal exception in interrupt [ 26.880000] Rebooting in 3 seconds..
On 08/12/2013 09:43 PM, cmsv wrote:
OpenWrt version: Attitude Adjustment (r37747)
Recently there was someone (Lucaspost) on #batman with a problem caused by mixing the latest AA and Batman-adv 2013.3.0 and while i can't be sure the problem is exactly this one; here goes my testing with a D-link 615C1
maybe you're mixing module and kernel versions?
try to "make dirclean" and rebuild
batadv.sh only does this
echo "$mesh" > "/sys/class/net/$iface/batman_adv/mesh_iface"
where $iface is something like "wlan0" and $mesh is "bat0"
HTH,
Gui
The problem has now been solved with the needed patch that was backported to AA. It is now available in r37768 and the images with batman-adv are not affected by this problem.
Patch is at: target/linux/generic/patches-3.3/721-phy_packets.patch
On 08/12/2013 08:59 PM, Gui Iribarren wrote:
On 08/12/2013 09:43 PM, cmsv wrote:
OpenWrt version: Attitude Adjustment (r37747)
Recently there was someone (Lucaspost) on #batman with a problem caused by mixing the latest AA and Batman-adv 2013.3.0 and while i can't be sure the problem is exactly this one; here goes my testing with a D-link 615C1
maybe you're mixing module and kernel versions?
try to "make dirclean" and rebuild
batadv.sh only does this
echo "$mesh" > "/sys/class/net/$iface/batman_adv/mesh_iface"
where $iface is something like "wlan0" and $mesh is "bat0"
HTH,
Gui
On Tue, Aug 13, 2013 at 10:48:15PM -0400, cmsv wrote:
The problem has now been solved with the needed patch that was backported to AA. It is now available in r37768 and the images with batman-adv are not affected by this problem.
Patch is at: target/linux/generic/patches-3.3/721-phy_packets.patch
Just to clarify: this patch existed before and the backported fix is "changing the patch" to avoid the crash :-)
Thanks for raising the issue!
Cheers,
Although things seem to be working i still see some warnings when restarting the wifi; that might be relevant:
# wifi command failed: Device or resource busy (-16) Configuration file: /var/run/hostapd-phy0.conf [ 1086.410000] device wlan0 entered promiscuous mode Using interface [ 1086.430000] br-lan: port 2(wlan0) entered forwarding state wlan0 with hwadd[ 1086.430000] br-lan: port 2(wlan0) entered forwarding state r 00:22:b0:d2:61:0b and ssid "test.net" [ 1088.430000] br-lan: port 2(wlan0) entered forwarding state Successfully initialized wpa_supplicant
[ 1090.690000] ------------[ cut here ]------------ [ 1090.700000] WARNING: at /home/cmsv/attitude_adjustment/build_dir/linux-ar71xx_generic/compat-wireless-2013-06-27/net/mac80211/chan.c:218 0x80ca631c()
[ 1090.710000] Modules linked in: ath79_wdt ledtrig_timer ledtrig_netdev batman_adv(O) nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp ipt_MASQUERADE iptable_nat nf_nat xt_conntrack xt_CT xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ath9k(O) ath9k_common(O) ath9k_hw(O) ath(O) mac80211(O) nls_base libcrc32c crc16 cfg80211(O) compat(O) arc4 aes_generic crc32c crypto_hash crypto_algapi ledtrig_default_on leds_gpio gpio_button_hotplug(O) [ 1090.760000] Call Trace:[<8027b518>] 0x8027b518 [ 1090.770000] [<8027b518>] 0x8027b518 [ 1090.770000] [<80071a8c>] 0x80071a8c [ 1090.770000] [<80ca631c>] 0x80ca631c [ 1090.780000] [<80071ad0>] 0x80071ad0 [ 1090.780000] [<80ca631c>] 0x80ca631c [ 1090.790000] [<80ca6814>] 0x80ca6814 [ 1090.790000] [<80ca1da4>] 0x80ca1da4 [ 1090.790000] [<80ce376c>] 0x80ce376c [ 1090.800000] [<80ca6d5c>] 0x80ca6d5c [ 1090.800000] [<80c95b24>] 0x80c95b24 [ 1090.800000] [<80c1f958>] 0x80c1f958 [ 1090.810000] [<8020b5dc>] 0x8020b5dc [ 1090.810000] [<801f9080>] 0x801f9080 [ 1090.810000] [<8020b410>] 0x8020b410 [ 1090.820000] [<8020a9ec>] 0x8020a9ec [ 1090.820000] [<8020b400>] 0x8020b400 [ 1090.820000] [<8020a344>] 0x8020a344 [ 1090.830000] [<801e05ac>] 0x801e05ac [ 1090.830000] [<8020a730>] 0x8020a730 [ 1090.830000] [<8025eaac>] 0x8025eaac [ 1090.840000] [<801e12fc>] 0x801e12fc [ 1090.840000] [<801d7cb4>] 0x801d7cb4 [ 1090.840000] [<801e4860>] 0x801e4860 [ 1090.850000] [<8025e690>] 0x8025e690 [ 1090.850000] [<80094804>] 0x80094804 [ 1090.860000] [<80092214>] 0x80092214 [ 1090.860000] [<800c2b1c>] 0x800c2b1c [ 1090.860000] [<801e392c>] 0x801e392c [ 1090.870000] [<801d8cf0>] 0x801d8cf0 [ 1090.870000] [<800c557c>] 0x800c557c [ 1090.870000] [<800c59d4>] 0x800c59d4 [ 1090.880000] [<8006c0c4>] 0x8006c0c4 [ 1090.880000] [<800e91e0>] 0x800e91e0 [ 1090.880000] [<800e96f4>] 0x800e96f4 [ 1090.890000] [<801da5cc>] 0x801da5cc [ 1090.890000] [<80096ae0>] 0x80096ae0 [ 1090.890000] [<800e9f78>] 0x800e9f78 [ 1090.900000] [<800d70a4>] 0x800d70a4 [ 1090.900000] [<8006a284>] 0x8006a284 [ 1090.900000] [ 1090.910000] ---[ end trace c98f8801474471e6 ]---
On 08/14/2013 06:33 AM, Antonio Quartulli wrote:
On Tue, Aug 13, 2013 at 10:48:15PM -0400, cmsv wrote:
The problem has now been solved with the needed patch that was backported to AA. It is now available in r37768 and the images with batman-adv are not affected by this problem.
Patch is at: target/linux/generic/patches-3.3/721-phy_packets.patch
Just to clarify: this patch existed before and the backported fix is "changing the patch" to avoid the crash :-)
Thanks for raising the issue!
Cheers,
b.a.t.m.a.n@lists.open-mesh.org