Hi Patrick,

after reading your text three times I still don't understand your setup. :) Maybe its just me, but unless someone else answers, maybe you can help me:

* Where is that Linksys router you have in that network drawing? * With Client/Gateway mode, are you referring to batman-adv gateway feature? * Could you perhaps simplify your explanation to one specific case where it "slow" where you don't expect it to be? Also, it would be helpful to minimize the network setup for this case and describe it one more time (including all ports). * Also, another helpful thing would be to post your "batctl if" output to see which devices are part of the the batman interface

From your explanation, it sounds like you have some kind of bridge loop going on in your network. Maybe you can check whether you have lots of broadcast packets coming in (e.g. by using tcpdump or batctl td).

Thanks, Simon

On Thursday 09 July 2015 16:12:12 Patrick Bosch wrote:

Hello everyone

I'm trying to set up a mesh, but I'm running into some issues, where I'm not sure if I'm doing something wrong or if there is a bug hidden somewhere.

I'm using the Nanostation M5 XW with OpenWRT Chaos Calmer RC2 and only OpenWRT packages. The trouble occurs on a Nanostation in client mode, not in gateway mode.

My setup:

Laptop --- Client-mode --- Linksys router --- Gateway-mode

                                 ----------WiFi-----------

Laptop is connected to secondary port. The main port is connected through a wire, the interface is not bridged to bat0. On the gateway, the main and secondary port are bridged to bat0. The main port is used for the connection to the router.

What I'm trying to do is set up a mesh through WiFi and bridged to it is the secondary port of the Nanostation. There will be clients connected to it at some point. The main port is not bridged as this is connected to a network that has to be completely isolated. The main port is used for PoE and as a debugging connection with SSH. If I bridge it, it simply uses the wired connection, which is not intended. But even so, I still see Batman messages on the interface for the main port, although it is not bridged. If I don't connect any data to the main port, only power, it seems to work fine. As soon as I connect it to data, I see two things. First, on the bat0 interface messages with the same source and destination arrive. Second, the SSH connection to the client Nanostation becomes really bad from time to time, but not consistently. My computer is connected to the secondary port of the Nanostation. Both of these occurrences seem to correlate, but both are not consistent.

As far as I understand it, batman advanced should not use the wired interface on the client Nanostation. But it sends packets on that interface. I think the problem of the bad performance lies also there, but I am not sure. I hope somebody can help me. Following are my configurations:

Network:

config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0'

config switch option name 'switch0' option reset '1' option enable_vlan '1'

config switch_vlan option device 'switch0' option vlan '1' option ports '0t 1'

config switch_vlan option device 'switch0' option vlan '2' option ports '0t 5'

config interface 'mesh' option mtu '1532' option proto 'batadv' option mesh 'bat0'

config interface 'bat0' option ifname 'bat0' option proto 'none' option mtu '1532'

config interface 'br' option type 'bridge' option ifname 'eth0.1 bat0' option proto 'static' option ipaddr '10.123.0.2' option netmask '255.255.255.0'

config interface 'wan' option proto 'dhcp' option ifname 'eth0.2' option hostname 'iFEST2' option defaultroute '0'

config interface 'wan6' option proto 'dhcpv6' option reqaddress 'try' option reqprefix 'auto' option ifname 'eth0.2'

Wireless:

config wifi-device radio0 option type 'mac80211' option hwmode '11a' option path 'platform/ar934x_wmac' option htmode 'HT20' option channel '40' option txpower '17' option country 'BE' option disabled '0'

config wifi-iface option device 'radio0' option ifname 'adhoc0' option encryption 'psk2' option network 'mesh' option ssid 'mySSID' option mode 'adhoc' option bssid '02:CA:FE:CA:CA:40' option mcast_rate '18000' option key 'myKey'

Batman:

config 'mesh' 'bat0' option 'aggregated_ogms' option 'ap_isolation' option 'bonding' option 'fragmentation' option 'gw_bandwidth' option 'gw_mode' 'client' option 'gw_sel_class' option 'log_level' option 'orig_interval' option 'vis_mode' option 'bridge_loop_avoidance' '1' option 'distributed_arp_table' option 'multicast_mode' option 'network_coding' option 'hop_penalty' option 'isolation_mark'

These are two different translocal tables that I get, 04:18:d6:61:81:54 is the MAC of the node in question:

Locally retrieved addresses (from bat0) announced via TT (TTVN: 28): Client VID Flags Last seen (CRC )

• 9e:90:31:79:cd:b8 -1 [.P....] 0.000 (0x02c4aa75)
• 9e:90:31:79:cd:b8 0 [.P....] 0.000 (0x4620303d)
• e8:80:2e:e7:a4:df -1 [......] 0.730 (0x02c4aa75)

Locally retrieved addresses (from bat0) announced via TT (TTVN: 29): Client VID Flags Last seen (CRC )

• 9e:90:31:79:cd:b8 -1 [.P....] 0.000 (0xd3ed0426)
• 04:18:d6:61:81:54 -1 [......] 30.370 (0xd3ed0426)
• 9e:90:31:79:cd:b8 0 [.P....] 0.000 (0x4620303d)
• e8:80:2e:e7:a4:df -1 [......] 0.010 (0xd3ed0426)

The transglobal one, 04:18:d6:61:81:68 is the MAC of the gateway

Globally announced TT entries received via the mesh bat0 Client VID (TTVN) Originator (Curr TTVN) (CRC ) Flags

• da:2b:ea:63:42:38 0 ( 32) via 04:18:d6:60:81:68 ( 71)

(0x9079f118) [....]

• 04:18:d6:61:81:54 -1 ( 71) via 04:18:d6:60:81:68 ( 71)

(0x4bb17292) [....]

• 04:18:d6:61:81:68 -1 ( 32) via 04:18:d6:60:81:68 ( 71)

(0x4bb17292) [....]

• da:2b:ea:63:42:38 -1 ( 32) via 04:18:d6:60:81:68 ( 71)

(0x4bb17292) [....]

Kind regards Patrick