I think you shouldn't use 169.254.0.0 as ip... try using 169.254.0.1 instead
2011/4/25 Krzysiek Gołębiewski gollab@interia.pl:
Hello all!
From quite long time I was trying to configure batmand. I am a student and my M.A. thesis is based on MESH. I have chosen a batman_adv and batmand to compare it (performance f.e). Batman_adv is working for me (I used an instruction from another page) and now I would like to configure batmand. Finally I have found this website.
My devices: Now I have Asus WL-500gPremium router with Mini PCI Atheros inside. On both routers there is Backfire 10.03.1-rc4. I have installed a package batmand (Version: r1439-1) and also kmod-tun, libpthread and kmod-batgat too.
Thanks to earlier posts in this archive I could run batmand and do some configuration (based on posts from another users from here and some own initiative and ideas.
Now my settings are:
GATEWAY:
/ETC/CONFIG/WIRELESS:
config 'wifi-device' 'wifi0' option 'type' 'atheros' option 'disabled' '0' option 'channel' '1' option 'txpower' '1' option 'hwmode' '11g'
config 'wifi-iface' option 'device' 'wifi0' option 'encryption' 'none' option 'ssid' 'potato' option 'bssid' '01:CA:FF:EE:BA:BE' option 'swmerge' '1' option 'mode' 'adhoc'
/ETC/CONFIG/NETWORK:
config 'switch' 'eth0' option 'enable' '1'
config 'switch_vlan' 'eth0_0' option 'device' 'eth0' option 'vlan' '0' option 'ports' '1 2 3 4 5'
config 'switch_vlan' 'eth0_1' option 'device' 'eth0' option 'vlan' '1' option 'ports' '0 5'
config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0'
config 'interface' 'wan' option 'ifname' 'eth0.1' option 'proto' 'dhcp' #option 'proto' 'static' #option 'ipaddr' '10.130.1.1' #option 'netmask' '255.255.255.0'
config 'interface' 'lan' #option 'type' 'bridge' option 'ifname' 'eth0.0' option 'proto' 'static' option 'ipaddr' '192.168.3.1' option 'netmask' '255.255.255.0'
config 'interface' 'ath0' option 'ifname' 'ath0' option 'proto' 'static' option 'ipaddr' '10.130.1.1' option 'netmask' '255.255.255.0'
/ETC/CONFIG/FIREWALL
config defaults option syn_flood 1 option input ACCEPT option output ACCEPT option forward REJECT
config zone option name lan option input ACCEPT option output ACCEPT option forward REJECT
config zone option name wan option input REJECT option output ACCEPT option forward REJECT option masq 1 option mtu_fix 1
config forwarding option src lan option dest wan
config forwarding option src wan option dest lan
# We need to accept udp packets on port 68, # see https://dev.openwrt.org/ticket/4108 config rule option src wan option proto udp option dest_port 68 option target ACCEPT
#Allow ping config rule option src wan option proto icmp option icmp_type echo-request option target ACCEPT
# include a file with users custom iptables rules config include option path /etc/firewall.user
### EXAMPLE CONFIG SECTIONS # do not allow a specific ip to access wan #config rule # option src lan # option src_ip 192.168.45.2 # option dest wan # option proto tcp # option target REJECT
# block a specific mac on wan #config rule # option dest wan # option src_mac 00:11:22:33:44:66 # option target REJECT
# block incoming ICMP traffic on a zone #config rule # option src lan # option proto ICMP # option target DROP
# port redirect port coming in on wan to lan #config redirect # option src wan # option src_dport 5001 # option dest lan # option dest_ip 192.168.3.1 # option dest_port 5001 # option proto tcp #config redirect # option src wan # option src_dport 5001 # option dest lan # option dest_ip 192.168.3.1 # option dest_port 5001 # option proto udp
### FULL CONFIG SECTIONS #config rule # option src lan # option src_ip 192.168.45.2 # option src_mac 00:11:22:33:44:55 # option src_port 80 # option dest wan # option dest_ip 194.25.2.129 # option dest_port 120 # option proto tcp # option target REJECT
#config redirect # option src lan # option src_ip 192.168.45.2 # option src_mac 00:11:22:33:44:55 # option src_port 1024 # option src_dport 80 # option dest_ip 194.25.2.129 # option dest_port 120 # option proto tcp
and one client (at least so far)
CLIENT:
/ETC/CONFIG/WIRELESS:
config 'wifi-device' 'wifi0' option 'type' 'atheros' option 'disabled' '0' option 'channel' '1' option 'txpower' '1' option 'hwmode' '11g'
config 'wifi-iface' option 'device' 'wifi0' option 'encryption' 'none' option 'ssid' 'potato' option 'bssid' '01:CA:FF:EE:BA:BE' option 'swmerge' '1' option 'mode' 'adhoc'
/ETC/CONFIG/NETWORK:
config 'switch' 'eth0' option 'enable' '1'
config 'switch_vlan' 'eth0_0' option 'device' 'eth0' option 'vlan' '0' option 'ports' '1 2 3 4 5'
config 'switch_vlan' 'eth0_1' option 'device' 'eth0' option 'vlan' '1' option 'ports' '0 5'
config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0'
config 'interface' 'wan' #option 'type' 'bridge' #list 'ifname' 'wifi0' #option 'ifname' 'eth0.1' #option 'dns' '10.130.1.1' #option 'defaultroute' '0' #option 'peerdns' '0' #option 'proto' 'static' #option 'ipaddr' '10.130.1.3' #option 'netmask' '255.255.255.0' #option 'gateway' '10.130.1.1'
config 'interface' 'lan' option 'ifname' 'eth0.0' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.4.1'
config 'interface' 'ath0' option 'ifname' 'ath0' option 'proto' 'static' option 'ipaddr' '10.130.1.3' option 'netmask' '255.255.255.0' option 'gateway' '10.130.1.1' option 'dns' '10.130.1.1'
/ETC/CONFIG/FIREWALL
config defaults option syn_flood 1 option input ACCEPT option output ACCEPT option forward REJECT
config zone option name lan option input ACCEPT option output ACCEPT option forward REJECT
config zone option name wan option input REJECT option output ACCEPT option forward REJECT option masq 1 option mtu_fix 1
config forwarding option src lan option dest wan
config forwarding option src wan option dest lan
# We need to accept udp packets on port 68, # see https://dev.openwrt.org/ticket/4108 config rule option src wan option proto udp option dest_port 68 option target ACCEPT
#Allow ping config rule option src wan option proto icmp option icmp_type echo-request option target ACCEPT
# include a file with users custom iptables rules config include option path /etc/firewall.user
### EXAMPLE CONFIG SECTIONS # do not allow a specific ip to access wan #config rule # option src lan # option src_ip 192.168.45.2 # option dest wan # option proto tcp # option target REJECT
# block a specific mac on wan #config rule # option dest wan # option src_mac 00:11:22:33:44:66 # option target REJECT
# block incoming ICMP traffic on a zone #config rule # option src lan # option proto ICMP # option target DROP
# port redirect port coming in on wan to lan #config redirect # option src wan # option src_dport 5001 # option dest lan # option dest_ip 192.168.2.140 # option dest_port 5001 # option proto tcp #config redirect # option src wan # option src_dport 5001 # option dest lan # option dest_ip 192.168.2.140 # option dest_port 5001 # option proto udp
### FULL CONFIG SECTIONS #config rule # option src lan # option src_ip 192.168.45.2 # option src_mac 00:11:22:33:44:55 # option src_port 80 # option dest wan # option dest_ip 194.25.2.129 # option dest_port 120 # option proto tcp # option target REJECT
#config redirect # option src lan # option src_ip 192.168.45.2 # option src_mac 00:11:22:33:44:55 # option src_port 1024 # option src_dport 80 # option dest_ip 194.25.2.129 # option dest_port 120 # option proto tcp
I start batmand with:
On the Gateway: batmand -d 3 -g 11000 -a 192.168.3.0/24 --hop-penalty 5 --purge-timeout 50000 ath0
and on the client batmand -d 3 -r 2 -a 192.168.4.0/24 --disable-client-nat --hop-penalty 5 --purge-timeout 50000 ath0
Then I check all:
batmand -d1 -c On the gateway: Originator (#/255) Nexthop [outgoingIF]: Potential nexthops ... [B.A.T.M.A.N. 0.4-alpha rv1439, MainIF/IP: ath0/10.130.1.1, UT: 0d 0h 1m] 10.130.1.3 (234) 10.130.1.3 [ ath0]: 10.130.1.3 (234)
On the client: Originator (#/255) Nexthop [outgoingIF]: Potential nexthops ... [B.A.T.M.A.N. 0.4-alpha rv1439, MainIF/IP: ath0/10.130.1.3, UT: 0d 0h 3m] 10.130.1.1 (243) 10.130.1.1 [ ath0]: 10.130.1.1 (243)
batmand -d2 -c
On the gateway: Gateway (#/255) Nexthop [outgoingIF], gw_class ... [B.A.T.M.A.N. 0.4-alpha rv1439, MainIF/IP: ath0/10.130.1.1, UT: 0d 0h 2m] No gateways in range ...
On the client: I can see my gateway -> 10.130.1.1 Gateway (#/255) Nexthop [outgoingIF], gw_class ... [B.A.T.M.A.N. 0.4-alpha rv1439, MainIF/IP: ath0/10.130.1.3, UT: 0d 0h 4m] => 10.130.1.1 (255) 10.130.1.1 [ ath0], gw_class 184 - 12MBit/1536KBit, gateway failures: 0
Command ifconfig showed: on the gateway:
ath0 Link encap:Ethernet HWaddr 00:0E:8E:18:F7:91 inet addr:10.130.1.1 Bcast:10.130.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:517 errors:0 dropped:0 overruns:0 frame:0 TX packets:3301 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:28892 (28.2 KiB) TX bytes:213735 (208.7 KiB)
eth0 Link encap:Ethernet HWaddr 00:1A:92:7E:27:B7 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3709 errors:0 dropped:0 overruns:0 frame:0 TX packets:4320 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:351741 (343.4 KiB) TX bytes:754122 (736.4 KiB) Interrupt:4
eth0.0 Link encap:Ethernet HWaddr 00:1A:92:7E:27:B7 inet addr:192.168.3.1 Bcast:192.168.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3581 errors:0 dropped:0 overruns:0 frame:0 TX packets:2304 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:274574 (268.1 KiB) TX bytes:602269 (588.1 KiB)
eth0.1 Link encap:Ethernet HWaddr 00:1A:92:7E:27:B7 inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:111 errors:0 dropped:0 overruns:0 frame:0 TX packets:2017 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:9083 (8.8 KiB) TX bytes:105082 (102.6 KiB)
gate0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:169.254.0.0 P-t-P:169.254.0.0 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1471 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:214 errors:0 dropped:0 overruns:0 frame:0 TX packets:214 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18654 (18.2 KiB) TX bytes:18654 (18.2 KiB)
wifi0 Link encap:UNSPEC HWaddr 00-0E-8E-18-F7-91-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6600 errors:0 dropped:0 overruns:0 frame:696 TX packets:3933 errors:271 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:195 RX bytes:856392 (836.3 KiB) TX bytes:344114 (336.0 KiB) Interrupt:6
and on the client:
ath0 Link encap:Ethernet HWaddr 00:0E:8E:18:F7:AE inet addr:10.130.1.3 Bcast:10.130.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3805 errors:0 dropped:7 overruns:0 frame:0 TX packets:1236 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:192820 (188.3 KiB) TX bytes:83458 (81.5 KiB)
eth0 Link encap:Ethernet HWaddr 00:1A:92:7E:27:71 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4205 errors:0 dropped:0 overruns:0 frame:0 TX packets:3622 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:337594 (329.6 KiB) TX bytes:360497 (352.0 KiB) Interrupt:4
eth0.0 Link encap:Ethernet HWaddr 00:1A:92:7E:27:71 inet addr:192.168.4.1 Bcast:192.168.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4200 errors:0 dropped:0 overruns:0 frame:0 TX packets:3620 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:261741 (255.6 KiB) TX bytes:335861 (327.9 KiB)
gate0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:169.254.0.1 P-t-P:169.254.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1471 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:1260 (1.2 KiB)
gate1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:169.254.0.1 P-t-P:169.254.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1471 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:34 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2164 (2.1 KiB) TX bytes:2164 (2.1 KiB)
wifi0 Link encap:UNSPEC HWaddr 00-0E-8E-18-F7-AE-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43355 errors:0 dropped:0 overruns:0 frame:801 TX packets:1938 errors:333 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:195 RX bytes:4590804 (4.3 MiB) TX bytes:175638 (171.5 KiB) Interrupt:6
And route -n showed:
on the gateway:
Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.130.1.0 0.0.0.0 255.255.255.0 U 0 0 0 ath0 192.168.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0.0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0.1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 gate0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0.1
and on the client:
Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0.0 10.130.1.0 0.0.0.0 255.255.255.0 U 0 0 0 ath0 0.0.0.0 10.130.1.1 0.0.0.0 UG 0 0 0 ath0
I added also a registration to iptable (on the gateway and on the client the same) iptables -t nat -I POSTROUTING -o gate0 -j MASQUERADE
So, nodes can see each other, and the gateway is broadcasting (client can see it). I can ping from gateway to client by tunnel -> ping 169.254.0.0 but I can`t ping from client to gateway -> ping 169.254.0.0 , what`s wrong? Unfortunately, I can`t get internet too.
Can somebody help me? I suppose there is a small mistake, as always but I have recently started my adventures with Open Wrt so I don`t understand everything and it can be my mistake. Thanks in Advance, Krzysiek (student).
Ustaw Interie jako strone startowa! Zobacz jak to zrobic >> http://linkint.pl/f297e