Repository : ssh://git@open-mesh.org/doc

On branches: backup-redmine/2017-07-13,master

commit 76fbc080cc2102e2cc87f0d1379ed330928e8d9f Author: Marek Lindner mareklindner@neomailbox.ch Date: Sun Nov 9 17:48:15 2008 +0000

doc: batmand/RoutingVodoo

76fbc080cc2102e2cc87f0d1379ed330928e8d9f batmand/RoutingVodoo.textile | 79 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 79 insertions(+)

diff --git a/batmand/RoutingVodoo.textile b/batmand/RoutingVodoo.textile new file mode 100644 index 00000000..19983565 --- /dev/null +++ b/batmand/RoutingVodoo.textile @@ -0,0 +1,79 @@ +With version 0.3 batman became "policy routing" support and thus can use special routing functions provided by the Linux kernel. + +This document explains its purpose and tries to point out why batman is doing it. Please keep in mind: Normally, you wont have to to anything about it ! Batman will take care of all the routing work but it might prove helpful to understand what batman does and why. ;-) + + +'''Routing tables''' + +Linux provides much more routing tables than just the one you can see with the "route" command. Batman makes use of the feature to spread its routing entries over 4 routing tables. To find out which routing tables are used issue "batmand -i" and watch out for the "rt_table" information: + +batmand -i | grep rt_table + +rt_table_networks=65 + +rt_table_hosts=66 + +rt_table_unreach=67 + +rt_table_tunnel=68 + +In the "networks" table you'll find routing entries for announced networks (HNA). + +The "hosts" table contains the entries to all reachable batman nodes. + +The "unreachable" table has a special funtion which will be explained later in this document (purpose section). + +The "tunnel" table contains the default route if the batman client uses the routing_class option and a gateway is available. + +The "route" command provides access to routing table 254. To see or manipulate the routing entries in the other tables you need the "ip" command. It should be shipped with your distribution. To see the content of the hosts table use: + +ip route ls table 66 + + +'''Routing rules''' + +Additionally to more routing tables, Linux offers to set routing rules which opens the possibility to control the packet flow. A rule can be based on certain criteria as source IP / destination IP / incoming interface / etc and will always target a routing table. When a new packet comes in, the kernel will follow the rules from the smallest available rule number until a rule is matched. Then the kernel jumps to the routing table which is pointed to by the rule and tries to find a routing entry there. If nothing is found the routing table will be left and the kernel proceeds with the next rule. Issue "batmand -i" to get the rule numbers used by batman: + +batmand -i | grep rt_prio + +rt_prio_default=6600 + +rt_prio_unreach=6700 + +rt_prio_tunnel=6800 + +To see the rules set by batman use the ip command: + +ip rule + +[..]? + +6600: from all to 105.0.0.0/8 lookup 66 + +6699: from all lookup 65 + +6700: from all to 105.0.0.0/8 lookup 67 + +[..]? + +On a minimal setup batman will set the rules shown above. + +The first rule says: If the packet has a destination IP in the range of 105.0.0.0/8 go to routing table 66 and look if you can find something there. + +The next rule means: All packets should go through our "network" (HNA) table. + +The last rule is similar to the first rule but the kernel will jump to our "unreachable" table. + + +'''What is the purpose of all this ?''' + + 1. Batman can clearly seperate hosts from announced networks. With a simple lookup you can see whether a node is announced or runs batman. + 2. It allows you and batman to easily delete all batman related table entries because the batman tables are well known and distinct. + 3. All batman activity is hidden in the background and does not mess with your manual configuration. You can still manipulate the default table without disturbing batman. + 4. It makes batman more interoperable with other routing protocols. This is very useful for testing scenarios where you want to test two (or more) routing protocols at the same time. + 5. With the unreachable rule we can make batman "faster". Whenever you want to access a node within your network which does not exist, your packets will end in the default route. You never will get an answer until your programm reaches a timeout. The unreachable rule changes this: If the packets destination is in your mesh network and no route exists, the kernel will immediately drop the packet and inform the programm which sent it. + 6. The policy routing "protects" your default route from other nodes. Batman will setup rules around the "tunnel" routing table which make sure that only non-batman interfaces and local traffic can end in the tunnel default route. You can choose your gateway as you like while this decission does not affect others in the network. + 7. The policy routing can be used for many more things, e.g. protecting against announced networks which have the same IP range as your internal network. Without policy routing it happens that you can't reach your internal network anymore because someone else announces the same IP range and your router sends the traffic there. However, this can't be done automatically by batman as the network configurations are too different. Firmware maintainers can tightly integrate batman into their distribution and add this feature. + + +If you want to influence batmans routing policy use the --policy-routing-script option to provide a custom executable. If this option is used batman will send it routing decissions to stdin of that executable instead of manipulation the routing table directly. Now, this executable can alter the rules and routing table entries by manipulating the routing by itself. You can see http://downloads.open-mesh.org/batman/useful-scripts-and-tools/policy_routin... to get a routing script sample. You wont need this option / script unless you want to do something fancy. \ No newline at end of file