Author: marek Date: 2010-05-04 03:46:24 +0200 (Tue, 04 May 2010) New Revision: 1651
Modified: trunk/batman-adv-kernelland/README Log: batman-adv: updating README
Signed-off-by: Marek Lindner lindner_marek@yahoo.de
Modified: trunk/batman-adv-kernelland/README =================================================================== --- trunk/batman-adv-kernelland/README 2010-05-02 23:24:27 UTC (rev 1650) +++ trunk/batman-adv-kernelland/README 2010-05-04 01:46:24 UTC (rev 1651) @@ -1,186 +1,259 @@ -[state: 22-03-2010] +[state: 03‐05‐2010]
-BATMAN-ADV ----------- +BATMAN‐ADV +‐‐‐‐‐‐‐‐‐‐
-Batman-advanced is a new approach to wireless networking which does no longer -operate on the IP basis. Unlike B.A.T.M.A.N, which exchanges information -using UDP packets and sets routing tables, batman-advanced operates on ISO/OSI -Layer 2 only and uses and routes (or better: bridges) Ethernet Frames. It -emulates a virtual network switch of all nodes participating. Therefore all -nodes appear to be link local, thus all higher operating protocols won't be -affected by any changes within the network. You can run almost any protocol -above B.A.T.M.A.N. Advanced, prominent examples are: IPv4, IPv6, DHCP, IPX. +Batman advanced is a new approach to wireless networking which +does no longer operate on the IP basis. Unlike the batman daemon, +which exchanges information using UDP packets and sets routing +tables, batman‐advanced operates on ISO/OSI Layer 2 only and uses +and routes (or better: bridges) Ethernet Frames. It emulates a +virtual network switch of all nodes participating. Therefore all +nodes appear to be link local, thus all higher operating proto‐ +cols won’t be affected by any changes within the network. You can +run almost any protocol above batman advanced, prominent examples +are: IPv4, IPv6, DHCP, IPX.
-This is batman-advanced implemented as Linux kernel driver. It does not depend -on any network (other) driver, and can be used on wifi as well as ethernet, -vpn, etc ... (anything with ethernet-style layer 2). -It compiles against and should work with Linux 2.6.20 - 2.6.33. Supporting older -versions is not planned, but it's probably easy to backport it. If you work on a -backport, feel free to contact us. :-) +Batman advanced was implemented as a Linux kernel driver to re‐ +duce the overhead to a minimum. It does not depend on any (other) +network driver, and can be used on wifi as well as ethernet lan, +vpn, etc ... (anything with ethernet‐style layer 2). It compiles +against and should work with Linux 2.6.21 ‐ 2.6.33. Supporting +older versions is not planned, but it’s probably easy to backport +it. If you work on a backport, feel free to contact us. :‐)
+ COMPILE -------- -To compile against your currently installed kernel, just type: +‐‐‐‐‐‐‐
+To compile against your currently installed kernel, just type: + # make
if you want to compile against some other kernel, use:
# make KERNELPATH=/path/to/kernel
-USAGE ------
-insmod the batman-adv.ko in your kernel: +CONFIGURATION +‐‐‐‐‐‐‐‐‐‐‐‐‐
-# insmod batman-adv.ko +Load the batman‐adv module into your kernel:
-the module is now waiting for activation. You must add some interfaces -on which batman can operate. Each interface must be added separately: +# insmod batman‐adv.ko
-# echo wlan0 > /proc/net/batman-adv/interfaces +The module is now waiting for activation. You must add some in‐ +terfaces on which batman can operate. After loading the module +batman advanced will scan your systems interfaces to search for +compatible interfaces. Once found, it will create subfolders in +the /sys directories of each supported interface, e.g.
-( # echo wlan1 > /proc/net/batman-adv/interfaces ) -( # echo eth0 > /proc/net/batman-adv/interfaces ) -( ... ) +# ls /sys/class/net/eth0/batman_adv/ +# iface_status mesh_iface
-Now batman starts broadcasting on this interface. -You can now view the table of originators (mesh participants) with: +If an interface does not have the "batman_adv" subfolder it prob‐ +ably is not supported. Not supported interfaces are: loopback, +non‐ethernet and batman’s own interfaces.
-# cat /proc/net/batman-adv/originators +Note: After the module was loaded it will continuously watch for +new interfaces to verify the compatibility. There is no need to +reload the module if you plug your USB wifi adapter into your ma‐ +chine after batman advanced was initially loaded.
-The module will create a new interface "bat0", which can be used as a -regular interface: +To activate a given interface simply write "bat0" into its +"mesh_iface" file inside the batman_adv subfolder:
-# ifconfig bat0 inet 192.168.0.1 up -# ping 192.168.0.2 -... +# echo bat0 > /sys/class/net/eth0/batman_adv/mesh_iface
---- -If you want topology visualization, your meshnode must be configured -as VIS-server: +Repeat this step for all interfaces you wish to add. Now batman +starts using/broadcasting on this/these interface(s).
-# echo "server" > /proc/net/batman-adv/vis_server +By reading the "iface_status" file you can check its status:
-Each node is either configured as "server" or as "client" (default: -"client"). Clients send their topology data to the server next to them, -and server synchronize with other servers. If there is no server -configured (default) within the mesh, no topology information will be -transmitted. With these "synchronizing servers", there can be 1 or -more vis servers sharing the same (or at least very similar) data. +# cat /sys/class/net/eth0/batman_adv/iface_status +# active
-When configured as server, you can get a topology snapshot of your mesh: +To deactivate an interface you have to write "none" into its +"mesh_iface" file:
-# cat /proc/net/batman-adv/vis_data +# echo none > /sys/class/net/eth0/batman_adv/mesh_iface
-This raw output is intended to be easily parsable and convertable with -other tools. Have a look at the batctl README if you want a vis output -in dot or json format for instance and how those outputs could then be -visualised in an image.
-The raw format consists of comma seperated values per entry where each -entry is giving information about a certain source interface. Each entry -can/has to have the following values: --> "mac" -> mac address of an originator's source interface - (each line begins with it) --> "TQ mac value" -> src mac's link quality towards mac address of a neighbor - originator's interface which is being used for routing --> "HNA mac" -> HNA announced by source mac --> "PRIMARY" -> this is a primary interface --> "SEC mac" -> secondary mac address of source (requires preceeding --> PRIMARY) +All mesh wide settings can be found in batman’s own interface +folder:
-The TQ value has a range from 4 to 255 with 255 being the best. -The HNA entries are showing which hosts are connected to the mesh via bat0 -or being bridged into the mesh network. -The PRIMARY/SEC values are only applied on primary interfaces +# ls /sys/class/net/bat0/mesh/ +# aggregate_ogm originators transtable_global vis_mode +# orig_interval transtable_local vis_data
---- + +Some of the files contain all sort of status information regard‐ +ing the mesh network. For example, you can view the table of +originators (mesh participants) with: + +# cat /sys/class/net/bat0/mesh/originators + +Other files allow to change batman’s behaviour to better fit your +requirements. For instance, you can check the current originator +interval (value in milliseconds which determines how often batman +sends its broadcast packets): + +# cat /sys/class/net/bat0/mesh/orig_interval +# status: 1000 + +and also change its value: + +# echo 3000 > /sys/class/net/bat0/mesh/orig_interval + In very mobile scenarios, you might want to adjust the originator -interval to a lower value. This will make the mesh more responsive to -topology changes, but will also increase the overhead. Please make sure -that all nodes in your mesh use the same interval. The default value -is 1000 ms (1 second). +interval to a lower value. This will make the mesh more respon‐ +sive to topology changes, but will also increase the overhead.
-# echo 1000 > /proc/net/batman-adv/orig_interval
-To deactivate batman, do: +USAGE +‐‐‐‐‐
-# echo "" > /proc/net/batman-adv/interfaces +To make use of your newly created mesh, batman advanced provides +a new interface "bat0" which you should use from this point on. +All interfaces added to batman advanced are not relevant any +longer because batman handles them for you. Basically, one "hands +over" the data by using the batman interface and batman will make +sure it reaches its destination.
+The "bat0" interface can be used like any other regular inter‐ +face. It needs an IP address which can be either statically con‐ +figured or dynamically (by using DHCP or similar services): + +# NodeA: ifconfig bat0 192.168.0.1 +# NodeB: ifconfig bat0 192.168.0.2 +# NodeB: ping 192.168.0.1 + +Note: In order to avoid problems remove all IP addresses previ‐ +ously assigned to interfaces now used by batman advanced, e.g. + +# ifconfig eth0 0.0.0.0 + + +VISUALIZATION ‐‐‐‐‐‐‐‐‐‐‐‐‐ + +If you want topology visualization, at least one mesh node must +be configured as VIS‐server: + +# echo "server" > /sys/class/net/bat0/mesh/vis_mode + +Each node is either configured as "server" or as "client" (de‐ +fault: "client"). Clients send their topology data to the server +next to them, and server synchronize with other servers. If there +is no server configured (default) within the mesh, no topology +information will be transmitted. With these "synchronizing +servers", there can be 1 or more vis servers sharing the same (or +at least very similar) data. + +When configured as server, you can get a topology snapshot of +your mesh: + +# cat /sys/class/net/bat0/mesh/vis_data + +This raw output is intended to be easily parsable and convertable +with other tools. Have a look at the batctl README if you want a +vis output in dot or json format for instance and how those out‐ +puts could then be visualised in an image. + +The raw format consists of comma separated values per entry where +each entry is giving information about a certain source inter‐ +face. Each entry can/has to have the following values: +‐> "mac" ‐ mac address of an originator’s source interface + (each line begins with it) +‐> "TQ mac value" ‐ src mac’s link quality towards mac address + of a neighbor originator’s interface which + is being used for routing +‐> "HNA mac" ‐ HNA announced by source mac +‐> "PRIMARY" ‐ this is a primary interface +‐> "SEC mac" ‐ secondary mac address of source + (requires preceding PRIMARY) + +The TQ value has a range from 4 to 255 with 255 being the best. +The HNA entries are showing which hosts are connected to the mesh +via bat0 or being bridged into the mesh network. The PRIMARY/SEC +values are only applied on primary interfaces + + LOGGING/DEBUGGING ------------------ +‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
-All error messages, warnings and information messages are sent to the -kernel log. Depending on your operating system distribution this can be -read in one of a number of ways. Try using the commands: dmesg, -logread, or looking in the files /var/log/kern.log or -/var/log/syslog. All batman-adv messages are prefixed with -"batman-adv:" So to see just these messages try +All error messages, warnings and information messages are sent to +the kernel log. Depending on your operating system distribution +this can be read in one of a number of ways. Try using the com‐ +mands: dmesg, logread, or looking in the files /var/log/kern.log +or /var/log/syslog. All batman‐adv messages are prefixed with +"batman‐adv:" So to see just these messages try
-dmesg | grep batman-adv +# dmesg | grep batman‐adv
-When investigating problems with your mesh network it is sometimes -necessary to see more detail debug messages. This must be enabled when -compiling the batman-adv module. When building batman-adv as part of -kernel, use "make menuconfig" and enable the option -"B.A.T.M.A.N. debugging". When compiling outside of the kernel tree it -is necessary to edit the file Makefile.kbuild and uncomment the line +When investigating problems with your mesh network it is some‐ +times necessary to see more detail debug messages. This must be +enabled when compiling the batman‐adv module. When building bat‐ +man‐adv as part of kernel, use "make menuconfig" and enable the +option "B.A.T.M.A.N. debugging". When compiling outside of the +kernel tree it is necessary to edit the file Makefile.kbuild and +uncomment the line
-#EXTRA_CFLAGS += -DCONFIG_BATMAN_ADV_DEBUG +#EXTRA_CFLAGS += ‐DCONFIG_BATMAN_ADV_DEBUG
-The additional debug output is by default disabled. It can be enabled -either at kernel modules load time or during run time. To enable debug -output at module load time, add the module parameter debug=<value>. -<value> can take one of four values. +The additional debug output is by default disabled. It can be en‐ +abled either at kernel modules load time or during run time. To +enable debug output at module load time, add the module parameter +debug=<value>. <value> can take one of four values.
-0 - All debug output disabled -1 - Enable messages related to routing / flooding / broadcasting -2 - Enable route or hna added / changed / deleted -3 - Enable all messages +0 ‐ All debug output disabled +1 ‐ Enable messages related to routing / flooding / broadcasting +2 ‐ Enable route or hna added / changed / deleted +3 ‐ Enable all messages
e.g.
-modprobe batman-adv debug=2 +# modprobe batman‐adv debug=2
-will load the module and enable debug messages for when routes or HNAs -change. +will load the module and enable debug messages for when routes or +HNAs change.
-The debug output can also be changed at runtime using the file -/sys/module/batman-adv/parameters/debug. e.g. +The debug output can also be changed at runtime using the file +/sys/module/batman‐adv/parameters/debug. e.g.
-echo 2 > /sys/module/batman-adv/parameters/debug +# echo 2 > /sys/module/batman‐adv/parameters/debug
enables debug messages for when routes or HNAs
-The debug output is sent to the kernel logs. So try dmesg, logread etc -to see the debug messages. +The debug output is sent to the kernel logs. So try dmesg, lo‐ +gread, etc to see the debug messages.
+ BATCTL ------- +‐‐‐‐‐‐
-B.A.T.M.A.N. advanced operates on layer 2 and thus all hosts partici- -pating in the virtual switch are completely transparent for all proto- -cols above layer 2. Therefore the common diagnosis tools do not work as -expected. To overcome these problems batctl was created. At the moment -the batctl contains ping, traceroute, tcpdump and interfaces to the -kernel module settings. +As batman advanced operates on layer 2 all hosts participating in +the virtual switch are completely transparent for all protocols +above layer 2. Therefore the common diagnosis tools do not work +as expected. To overcome these problems batctl was created. At +the moment the batctl contains ping, traceroute, tcpdump and +interfaces to the kernel module settings.
For more information, please see the manpage (man batctl).
-batctl is available on http://www.open-mesh.net/ +batctl is available on http://www.open%E2%80%90mesh.org/
+ CONTACT -------- +‐‐‐‐‐‐‐
Please send us comments, experiences, questions, anything :)
-IRC: #batman on irc.freenode.org -Mailing-list: b.a.t.m.a.n@open-mesh.net -(subscription at https://list.open-mesh.net/mm/listinfo/b.a.t.m.a.n ) +IRC: #batman on irc.freenode.org +Mailing‐list: b.a.t.m.a.n@open‐mesh.net (optional subscription + at https://lists.open%E2%80%90mesh.org/mm/listinfo/b.a.t.m.a.n)
You can also contact the Authors:
-Marek Lindner lindner_marek@yahoo.de -Simon Wunderlich siwu@hrz.tu-chemnitz.de +Marek Lindner lindner_marek@yahoo.de +Simon Wunderlich <siwu@hrz.tu‐chemnitz.de> +