30 Jan
2013
30 Jan
'13
8:30 p.m.
All,
I am trying to create a WiFi repeater using hardware that cannot accommodate a
normal "bridged repeater" mode. Is it possible to create this type of repeater
using BATMAN adv?
Thanks
Rip
30 Jan
30 Jan
10:03 p.m.
On Wed, Jan 30, 2013 at 08:30:52PM +0000, Rip route wrote:
All,
I am trying to create a WiFi repeater using hardware that cannot accommodate a
normal "bridged repeater" mode. Is it possible to create this type of repeater
using BATMAN adv?
If I correctly got your question you may want to connect two nodes via wireless,
then install batman-adv on top of the wifi interfaces ans consequently bridge
the bat0 with the ethernet interface:
wlan0~~~~~~~wlan0
. .
bat0 bat0
. .
br0 br0
. .
eth0 eth0
| |
ETH____/ \_______ETH
wlan0s can be two adhoc interfaces (common case for a mesh) or also an AP/sta
pair.
Cheers,
--
Antonio Quartulli
..each of us alone is worth nothing..
Ernesto "Che" Guevara
10:25 p.m.
Antonio Quartulli <ordex@...> writes:
wireless,
On Wed, Jan 30, 2013 at 08:30:52PM +0000, Rip route wrote:
> All,
> I am trying to create a WiFi repeater using hardware that cannot accommodate
a
> normal "bridged repeater" mode. Is it
possible to create this type of
repeater
using BATMAN
adv?
If I correctly got your question you may want to connect two nodes via then install batman-adv on top of the wifi interfaces
ans consequently bridge
the bat0 with the ethernet interface:
wlan0~~~~~~~wlan0
. .
bat0 bat0
. .
br0 br0
. .
eth0 eth0
| |
ETH____/ \_______ETH
wlan0s can be two adhoc interfaces (common case for a mesh) or also an AP/sta
pair.
Cheers,
Thanks but I need to create a repeater where I can't load anything on the root
AP, I can only access the repeater.
client1~~~~~wlan0~~~~~~~wlan0~~~~~~client2
|
ETH____/
10:28 p.m.
On Wed, Jan 30, 2013 at 10:25:27PM +0000, Rip route wrote:
Antonio Quartulli <ordex@...> writes:
wireless,
I think this detail depends on how you decide to configure the bridging on the
root AP. batman-adv will simply provide you the connectivity between the wifi
devices and the "possibility" to create a bridge. Then it's up to you how
to
configure it all.
Cheers,
--
Antonio Quartulli
..each of us alone is worth nothing..
Ernesto "Che" Guevara
On Wed, Jan 30, 2013 at 08:30:52PM +0000, Rip route wrote:
> All,
> I am trying to create a WiFi repeater using hardware that cannot accommodate
a
> normal "bridged repeater" mode. Is
it possible to create this type of
repeater
using
BATMAN adv?
If I correctly got your question you may want to connect two nodes via then install batman-adv on top of the wifi
interfaces ans consequently bridge
the bat0 with the ethernet interface:
wlan0~~~~~~~wlan0
. .
bat0 bat0
. .
br0 br0
. .
eth0 eth0
| |
ETH____/ \_______ETH
wlan0s can be two adhoc interfaces (common case for a mesh) or also an AP/sta
pair.
Cheers,
Thanks but I need to create a repeater where I can't load anything on the root
AP, I can only access the repeater.
client1~~~~~wlan0~~~~~~~wlan0~~~~~~client2
|
ETH____/
3711
days inactive
3711
days old
b.a.t.m.a.n@lists.open-mesh.org
3 comments
2 participants
participants (2)
-
Antonio Quartulli -
Rip route